vB Easy Archive - HTC Kaiser -> Stuck in OEMSBL

Pages: 1

HTC Kaiser -> Stuck in OEMSBL
(Click here to view the original thread with full colors/images)

Posted by: gargiuseppe

Yes guy, don't ask me why it's happened, i am very stupid!

Reading into internet, i've seen that you uses the QPST App.

Now i am asking you if it's possible to flash via OEMSBL at least the Bootloader.

Plz Help, me and other users are fallen into this error!!

Posted by: red.octane.aero

Yes you CAN flash in bootloader.

Start it up in bootloader. Connect it to your computer...does it say USB? If so...you can flash your ROM still.

If not...you can try to flash via SD card.
Make sure you have HardSPL on your device. And also make sure you have more than 50% of battery left or you can plug in a charger just to make sure there is no power failure.
Make sure your SD card is FORMATTED so your phone can read it.

Get the ROM image you would like to use, normally namede RUU_Sign.nbh, and rename it to "KAISIMG.nbh" <--VERY IMPORTANT!

Plug the card into the phone, then enter boot loader mode by pressing down the Power and Camera buttons simultaneously, and using the stylus at the same time to press the RESET button at the left side. Continue pressing the two buttons for a few seconds after pressing and releasing the reset button until the bootloader screen appears.

You will first see a tri-color screen then the information on the card. Press power button to start flashing.

Once all these are done, press the reset button located at the bottom of the phone to reset the device.

Good luck.

Posted by: gargiuseppe

I know all you've written. thanx for the reply.

but my phone doesn't start in bootloader: its screen is dark. Also the bootloader is deleted!!!!

Now i can access to the Qualcomm Chip via USB with "Qualcomm Diagnostic Interface 6000" drivers. With MTTY.exe i obtain responses (es: setboot 1).

But i've seen that QPST (i've installed it) can do Backup & restore of the data into the pda.

then i was asking if it's possible to download to the phone the HardSpl (that i've deleted), and then flash the Os via Sd.

QPST Doesn't detect the phone on the com port assigned to the "Qualcomm Diagnostic Interface 6000" drivers.

Help PLZ!

Posted by: red.octane.aero

OUCH. Sorry man. Your phone is TOAST for right now. No known repair right now unless you have some way of reloading CE on your phone.

Posted by: gargiuseppe

..i've read that with other phones which mounts Qualcomm Chip, is possible to write to the flash.

Now i was asking here if it's possible also with my kaiser.

I've not asked in other categories because of the off topic "fault".

Posted by: jessepatty

Quote:

Originally Posted by gargiuseppe

I know all you've written. thanx for the reply.

but my phone doesn't start in bootloader: its screen is dark. Also the bootloader is deleted!!!!

Now i can access to the Qualcomm Chip via USB with "Qualcomm Diagnostic Interface 6000" drivers. With MTTY.exe i obtain responses (es: setboot 1).

But i've seen that QPST (i've installed it) can do Backup & restore of the data into the pda.

then i was asking if it's possible to download to the phone the HardSpl (that i've deleted), and then flash the Os via Sd.

QPST Doesn't detect the phone on the com port assigned to the "Qualcomm Diagnostic Interface 6000" drivers.

Help PLZ!

Make sure your using a com port below 10 with MITTY...it won't work on a com port over 10... Reassign the com port for the Qualcomm Diagnostic interface if it's over com10.

Don't feel bad. I followed the instructions on XDA to remove the "Radio from hell" from my $500 Tilt and my computer won't run frankenKaiser so I can't get past step 6 of the process so my Tilt is in the same exact state right now....

Until I can figure out why my WINxp doesn't see FrankenKaiser as a valid application and run it, I'm stuck with a wiped phone. UHG!

I'm freaking out right now as I NEED my phone for work email.

J